Dobrodošli na moj blog


Last Time Introduce How To Make Imitation Pomellato

Although reminiscent of Native American beadwork, these woven are much easier to make and don’t require a beading loom. Their low profile makes them comfortable to wear. The key to successfully stringing them is the FireLine beading thread. Lightweight yet strong, the strand threads easily through beading needles and has no trouble passing multiple times through a small seed bead. one • Cut a 28" (71cm) Replica Hermes Bracelet length of FireLine and thread a beading needle onto each end. String one turquoise seed bead, a pink bugle bead and the wire. two • Slide on another row of beads and bring both ends of the wire through all the beads in opposite directions. three • Repeat steps one and two to continue building the ring. Continue until you have a finished beaded length of 2¼" (6cm), or enough beading to wrap around the desired finger. four • To make a circle, bring both ends of the ring together and thread the beading needle in the opposite direction through the first row of beads. five • Tie the ends of the thread in a strong knot to secure the ring. Afun-loving timekeeper, this playful is dripping with sentiment. Whimsical heart, cupid and key wired, connected with jump rings or strung around the watchband. Since it’s made with heavyweight elastic, you won’t have to struggle with a clasp—simply pull the finished bracelet over your hand for a comfortable fit. one • Thread glass beads onto head pins and cut the head pin wire to about ¼" (6mm) above each bead. Turn a small loop in the wire with round-nose pliers. Slide each wired bead and metal charm onto a jump ring. two • Attach one side of the face to a piece of thick beading elastic with a no. 4 crimp tube. Use crimping pliers to flatten the crimp tube. three • Slide a few charms randomly onto the elastic four • Slide on more beads following the charms. Continue stringing on beads and charms until the total beaded length is about 6" (15cm) five • Secure the end of the elastic to the face with a no. 4 crimp tube. Flatten the crimp tube Cheap Hermes Clic H Bracelet and trim away any excess elastic tail with scissors. 2017 Replica Van Cleef & Arpels Jewelry Trendy These elegant Swarovski crystal cubes are simply hung from plain silver head and eye pins. The cubes swing freely to playfully catch and refract light with each turn of your head. one • Slide a black diamond cube bead onto a head pin and measure up about ⁄ 1 " (61mm). Make a loop in the wire. Trim away the excess wire with wire cutters. two • Slide an eye pin onto the open loop and then close it with round-nose pliers. three • Slide a jet diagonal cube onto the eye pin. four • Cut the eye pin wire to about ³⁄8" (1cm) above the bead and make a loop in the wire with round-nose pliers. Slide the loop onto the earwire and close the loop with pliers. twisted leaf ring These tiny flowering stems are Fake Hermes Kelly Dog Bracelet easy to create—just twist folded sterling wires together with your fingertips. Fresh-water pearl buds and miniature glass leaves are simply threaded onto the wires and then twisted into place. The length of the stems is completely adjustable. If you prefer, make smaller with a single bud and one or two leaves, or extend the stem and add more pearls and leaves to make a longer ring. one • Cut about 8" (20cm) of wire and thread a freshwater pearl onto one end, about 2½" (6cm) or so from the end of the wire. Twist the wires together three times to secure the bead two • Measure up about 7 ⁄8" (2cm) from the top of the twisted bead and then wrap one wire around the round-nose pliers to make a small loop that is open at the bottom with about ½" (13mm) of straight wire under the loop. This wire will form the center stem. three • Thread a leaf bead onto the open wire, hold the leaf ³⁄8" (1cm) away from the pearl,Hermes Collier de Chien Bracelet Replica The leaf will be trapped on a wire loop. Then tightly twist the wire loop three times to create a short stem. Twist the wire three times around the central stem. Repeat to add two more leaves, separating each addition with three twists around the center stem wire. four • Wrap the wire around the open end of the open loop shape to secure the opening. five • Open the loop on the post and lide on the loop at the top of the twisted wire. Use pliers to close and secure the loop.

<< 07/2018 >>




Powered by